Garage Door Closure Problems

Are you working with a garage door that will not close all the way? Maybe you have noticed that there are a couple of inches of space left after you attempt to close the garage and the garage door has stopped. Or, maybe the garage door will roll down, touch the ground, and then immediately roll back up again. Do any of these problems sound familiar to you? If so, you are definitely not alone, since homeowners experience these and other common closure issues with their garage doors every day.

If you own a garage that refuses to close all the way, rolls back up instead of shutting, or is behaving badly in other ways, there are several things you can try that may help fix the problem. If a quick fix described below does not work, make sure to call in a garage door expert to help you find the source of the issue and get your garage door functioning normally again.

The Door is Blocked

If there is anything in the way of the garage door’s path, it will not close all the way. Garage doors have built-in safety sensors of all kinds that protect homeowners and their belongings from injury and damage. If anything is in the way of the door, such as leaves, rocks, toys, or other items, the garage door will not close all the way and may even roll back up.

The Safety Sensor Has Been Triggered

The garage door safety sensor can be triggered any time something goes underneath the garage door while it is moving. Prior to safety sensors being mandatory for garage door makers to implement into their models, garage doors would move up and down without pause, regardless if someone was in the way of the moving garage door or not. Obviously, this was dangerous for children, pets, and families everywhere. With safety sensors now in place for the majority of garage door models, anytime someone runs under the garage door while it is moving, the garage door will automatically stop for safety reasons. While this safety mechanism is necessary and can even save lives, it can sometimes get confused.

The Photo Eye is Out of Alignment

On both sides of your garage door, there are two sensors near the bottom. These two sensors form an invisible beam between them that must match perfectly in order for the garage door to work. The photo eye sensors help to determine if something is blocking the patch of your garage door. When the beam between them is broken, the garage door will stop or reverse.

Sometimes, the photo eyes can become misaligned, causing them to mistakenly sense that something is in the way since the beam has been broken. If the photo eyes are out of alignment, you may be able to fix the problem yourself or you may want to call in a garage door expert to help you.

Broken Springs or Cables

You may experience garage door closure problems if one of the springs or cables of your garage is broken, worn, or faulty. For these kinds of issues, you will want to definitely rely on a garage door expert to help you. Garage door cables and springs can be difficult to repair, especially if you have never done so before. When it comes to these kinds of repairs or any issues involving your garage door springs, make sure to call a specialist to help you.

Door Closure Limit is Off

Your garage door might be failing to close all the way because the close limit is set to the wrong position. The garage door close limit setting is great when homeowners want to leave a few inches of space at the bottom of their garage door for their cats to run under or for increased airflow to their garage. However, if you want your garage door to be shut all of the way, it can be frustrating when this setting turns on or is activated seemingly without prompt.
Be sure to check the close limit setting on your garage door by consulting your garage door owner’s manual. It is possible with a simple change of a setting or a motor reset that you may be able to fix the problem on your own and get the garage door to close in the proper position.

Bent or Misaligned Tracks

It is also possible that your garage door is failing to close all the way because one of the tracks are bent or misaligned. Bent tracks can happen to garages from time to time for a variety of reasons and may cause the garage door to act differently, make loud noises, or fail to close properly.

Just like with broken springs or cables, if the tracks on your garage door appear to be the source of the problem, you will need to consult an expert. Attempting to fix a bent or broken track on your own may cause the garage door to collapse entirely, leaving you with an even bigger problem on your hands, as well as a potential injury. Garage door experts can address your problem with ease and efficiency. By calling a specialist, you will avoid additional damages or potential injuries to yourself.

Looking for a Garage Door Expert?

f you are having problems with your garage door in Sandy Springs, Georgia and need an expert to help you as soon as possible, call Turner Sandy Springs Garage Door, LLC! Residents in Sandy Springs have turned to our garage door technicians for years to help with garage door repairs, replacements, and upgrades of all kinds. With our professional garage door assistance, any issues you are having with your garage door can be resolved immediately. Set-up an appointment with one of our skilled garage door experts today! Turner Sandy Springs Garage Door, LLC is your top choice when it comes to garage door repairs, springs and cable replacements, track installations, and more! Call our team today!